|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CAP - Adaptor Plug The CAP Adaptor Plug is used with the CC10S Cable and converts RS232 communication to the Lakewood plug connection system on an RX Data Storage unit and DPX2 Data Pac data loggers.
|
IP12VX - 12 Volt Regulated Input Plug The IP12VX input plug has the same input/output configuration as an IPX plug with the exception that it has an internal regulator which supplies 12 volts on terminal 4 (normally the B+ connector).
|
IP24VBMA - 24 Volt Booster Input Plug The IP24VBMA is a 4-20mA Input Plug that boosts voltage levels up to 24 volts for sensors that require more than 12 volts.
|
IP25mV - 25 Millivolt Input Plug The IP25mV amplifies a 0-25 millivolt input into a 0 to 2.5 volt output.
|
| IP420FS - 4 to 20mA Input PlugThe IP420FS is an Input Plug that allows for easy hookup of 4-20 mA transmitters and sensors. It converts and filters a 4-20 mA input into a 0.5 to 2.5 volt output and features a quick response time of .410 milliseconds.
|
| IP5VX - 5 Volt Regulated Input PlugThe IP5VX input plug has the same input/output configuration as an IPX plug with the exception that it has an internal regulator which supplies 5 volts on terminal 4 (normally the B+ connector). The 5 volt regulator is powered from the internal auxiliary instrument battery when the plug is connected to a Lakewood Data Logger.
|
| IP6VX - 6 Volt Regulated Input PlugThe IP6VX input plug has the same input/output configuration as an IPX plug with the exception that it has an internal regulator which supplies 6 volts on terminal 4 (normally the B+ connector). The 6 volt regulator is powered from the internal auxiliary instrument battery when the plug is connected to a Lakewood Data Logger.
|
| IPBA100A - Bridge Amplifier by 100 Input PlugThe IPBA100 amplifies a 0-25 millivolt input into a 0 to 2.5 volt output. The powering of the 100X Millivolt bridge is provided with on-board excitation and this plug also features a zero adjustment.
|
| IPBA10A - Bridge Amplifier by 10 Input PlugThe IPBA10 amplifies a 0-25 millivolt input into a 0 to 2.5 volt output. The powering of the 10X Millivolt bridge is provided with on-board excitation and this plug also features a zero adjustment.
|
| IPCB100DG - Counter Buffer / Divide by 100 Gated Input PlugThe IPCB100DG buffers the pulse to ground at the input and pulses the Data Logger's strobe input every 100 counts.
|
| IPCB10DG - Counter Buffer / Divide by 10 Gated Input PlugThe IPCB10DG buffers the pulse to ground at the input and pulses the Data Logger’s strobe input every 10 counts.
|
| IPCO - Closed / Open Input PlugThe IP-CO outputs a short pulse when a contact closes and then opens again. This Plug may be used for pump runtime and flow monitoring.
|
IPCP - Charge and Power Input Plug The IPCP is an Input Plug that allows for external charging and power and hookup for the RX Data Storage unit and DPX2 Data Pac.
|
IPR12V - Remote 12 Volt Regulation Input Plug This input plug provides a regulated 12 volt output
|
| IPR5V - Remote 5 Volt Regulation Input PlugThis input plug provides a regulated 5 volt output
|
IPT - Temperature Input Plug The IPT Input Plug allows for easy hookup to Lakewood Thermistor Temperature Sensors.
|
| IPX - Standard Input PlugThe IPX Input Plug allows for easy hookup of 0 to 2.5 volt output transmitters or status switch contact sensors.
|
